Product Information
Previous Product 4 of 12 Next

Sanguinololu 1.3a - Basic Kit DIY

Build your own Sanguinololu! Includes stepper drivers excl € 71.42  incl Log in  Favorites Email Print + - Order
Share
- Sanguinololu 1.3a - Basic Kit DIY
Product information
Category Reprap electronics
Stock
10
MPN

sanguinololuDIYFULL

Description

Kit contents

This kit includes verything you need to build your Sanguinololu board:

7x Capacitor 0.1uF
1x Capacitor 4.7uF
1x FT232RL (pre soldered)
1x Usb connector
     (pre soldered)
1x LM7805
1x Capacitor 0.47uF
1x 2 way Screw terminal
1x Atmega644-20PU
     (pre programmed)
1x DIP-40 Socket
3x 1x40 male pin header
1x 2x40 male pin header
2x 1x40 female pin header
1x LED 3mm green
1x Resonator 16Mhz
1x switch
2x MOSFET P55NF06
4x Capacitor 100uF
2x Capacitor 10uF
1x Capacitor 1000uF
1x Resistor 1.5k
7x Resistor 100K
2x Resistor 10K
2x Resistor 4.7K
13x jumper

4x Stepstick Stepper drivers

Assembly instructions: Here

Sanguinololu Features

  • Small design - board is 100mm x 50mm (4" x 2") - barely an inch longer than a business card!
  • Sanguino clone, Atmel's ATmega644P 
  • Up to 4 Pololu (or Pololu compatible) on-board (X,Y,Z,Extruder) (A4983 without voltage regulator)
  • Supports multiple power configurations
-- Logic & Motors supplied by ATX power supply (needs molex harddrive connector, and optional 4pin atx connector for additional 12v/supply voltage)
-- Motors supplied by 5mm screw terminal 7-35V
-- Logic supplied by USB bus
-- Logic supplied by optional on-board voltage regulator (molex harddrive connector cannot be installed at the same time)
-- Supports multiple communication configurations
-- FT232RL on-board for USB connectivity
-- USB2TTL header is available for FTDI cable, or BlueSMIRF bluetooth module
  • 2 thermistor connectors with circuitry
  • 2 N-MOSFETs for extruder/bed, or whatever
  • Selectable 12v(or supply voltage)/5v endstop voltage
  • Edge connectors enabling right-angle connections
  • Silkscreen for connectors on both sides of the board, facilitating bottom cable connections
  • 13 Extra pins available for expansion and development - 6 analog and 8 digital, with the following capabilities
-- UART1 (RX and TX)
-- I2C (SDA and SCL)
-- SPI (MOSI, MISO, SCK)
-- PWM pin (1)
-- Analog I/O (5)

All through-hole components (except FTDI chip) for easy DIY soldering.

 

http://www.reprap.org/wiki/Sanguinololu

Kit contents
This product is a set of the following items:
Quantity Product
1x Sanguinololu 1.3a - DIY
4x Stepstick A4988 (Discontinued)
4x Heatsink for pololu / stepstick stepper drivers
Quick Search
Advanced Search search
Price breaks
Sanguinololu 1.3a - Basic Kit DIY
1 to 4 pieces: excl € 71.42 
incl € 86.42 
5 to 9 pieces: excl € 64.28 
incl € 77.78 
10+ pieces: excl € 57.14 
incl € 69.14