RAMPS 2560 Electronics - Atmega 2560 (Arduino-compatible)

 - Product Information
Versatile development board with the famous Atmgega2560 chip. You can upload your own program to the board using Arduino software.
excl € 19.99 
1x € 18.99 
Price breaks
1 - 9: excl € 19.99 
10 - 29: excl € 14.99 
30 - ...: excl € 9.99 
Need a larger quantity? Contact our Sales department.

Product information

MEGA2560

8719128322544

0

RAMPS

Documentation

Product description

Versatile development board with the famous Atmgega2560 chip. You can upload your own program to the board using Arduino software.

The RAMPS 2560 Electronics is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino, Mega Duemilanove or Diecimila.

This is a clone board with the CH340G USB-to-Serial chip.

Specifications

Processor

Technology AVR
Type ATmega2560
Frequency 16 MHz
Memory 256

Dimensions

Length 110 mm
Depth 54 mm
Height 14 mm
Price breaks
1 - 9: excl € 19.99 
10 - 29: excl € 14.99 
30 - ...: excl € 9.99 
Need a larger quantity? Contact our Sales department.

Processor

Technology AVR
Type ATmega2560
Frequency 16 MHz
Memory 256

Dimensions

Length 110 mm
Depth 54 mm
Height 14 mm
Description

This product is a carrier board or breakout board for TI’s DRV8825 stepper motor driver; we therefore recommend careful reading of the DRV8825 datasheet (1MB pdf) before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2.2 A output current per coil (see the Power Dissipation Considerations section below for more information).

Description DRV8825 Stepper Motor Driver Carrier, High Current   More info More info Name Pololu DRV8825 Driver Carrier Weight unit Gram(s) Weight No information/text available Favorites Favorites Shipping time
Description

This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-temperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 V to 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling). This board ships with 0.1″ male header pins included but not soldered in.

Overview

This product is a carrier board or breakout board for Allegro’s A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil (see the Power Dissipation Considerations section below for more information). Here are some of the driver’s key features:

  •     Simple step and direction control interface
  •     Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
  •     Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
  •     Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
  •     Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
  •     Short-to-ground and shorted-load protection

 

Description Official Pololu 2A stepper driver for driving stepper motors in your 3D printer   More info More info Name Pololu A4988 Stepper Motor Driver Carrier Weight unit Gram(s) Weight No information/text available Favorites Favorites Shipping time
Description

 

Character Size H-W 2.95 x 4.75mm
Colour Blue/white
Display Type Reflective STN
External Dimensions H-W-D 98 x 60 x 9.5mm
Fixing Hole Diameter 2.5mm
Number Of Characters - Lines 20 x 4
Operating Temperature Range -20 → +70°C

Tutorial on how to hook up to RAMPS:
LCD and RAMPS
You can use 2x2-wire cables and 1x4wire cable to hook it up. You will need to connect pin 15 and 16 for back light.

Character Size H-W 2.95 x 4.75mm
Colour Yellow-Green
Display Type Reflective STN
External Dimensions H-W-D 98 x 60 x 9.5mm
Fixing Hole Diameter 2.5mm
Number Of Characters - Lines 20 x 4
Operating Temperature Range -20 → +70°C
Description Good value blue LCD with 4 lines of 20 characters in white enabling you to autonomously control your 3D printer   More info More info Name LCD - 20X4 - blue/white Weight unit Gram(s) Weight No information/text available Favorites Favorites Shipping time

About RepRapWorld
ReprapWorld

ReprapWorld is the number one webshop for all your reprap supplies for your 3D printer. We have a large collection of 3D printer components, from our famous electronics lines to filament from our own production. And everything is at a very competitive price!

Contact

RepRapWorld B.V.
Wagenmaker 6a
2631RL Nootdorp
The Netherlands

Email: info@reprapworld.com
Tel: +31 (0) 85 - 009 15 31

Copyright 2009 - 2017 | RepRapWorld B.V.