Original HotEnd E3D 24V
New and improved! The E3D-v6 is smaller, easier to use and will give you a higher performance.
Here is the E3D-v6 TOP 9 improvements:
It's ready for the runway
There are people that say looks don't matter. They are wrong. The E3D-v6 makes your printer look cool! The filament will never want anything else. And your friends? Well, let's just say you will be the king of your printing club with the new and improved E3D-v6.
It has never been this easy
The E3D-v6 has made it possible that some parts could be eliminated in the assembly process. This makes assembly and maintenance very simple.
5 Star printing rate
It doesn't matter what you want to print with the E3D-v6. It will give you the high quality that you demand. The prints will be sharper and more accurate, whether you're printing small, middle, large or enormous. The E3D-v6 will keep on giving you prints to be proud of and to show off to your friends.
It will print anything
Due to the PTFE liner the E3D-v6 can print with different kinds of filament. It could already print ABS and PLA. But now it can also print RealFlex and NinjaFlex, just to name two.
Feeling hot, hot, hot!
If you're used to printing only at 175°C, just wait until you start using the E3D-v6. It can easily reach 300°C and with a thermocouple you can even hit 400°C. Another advantage is that it reaches 200°C in a mere 65 seconds.
You can trust me
The E3D-v6 is much more reliable than its predecessors. The manufacturer did a lot of redesigning and took long and hard looks at the manufacturing process. The heat-breaks are redesigned and the inside of the nozzle has had a make-over. Due to these improvements you will get a wonderful finish and reduced force/pressure needed to extrude/restart extrusion.
Make it your own
A standard E3D-v6 will have a 0.4 nozzle. This is enough to give you good quality prints, with a perfect balance in speed, ease and resolution. However, we offer a lot of different nozzles so you can experiment what suits you best and what sets you apart in your printing ventures.
Small, smaller, extra small
In creating the E3D-v6 special consideration was given at the size and mass of the nozzle. This resulted in a total length of just 62mm. A reduced mass in the x/y dimension was achieved by means of a new fan duct.
We will help you
If you have any problems or questions you can contact us through e-mail or telephone. You can even pop by our store in Nootdorp (The Netherlands) on weekdays. We're open till 5 o'clock and on Thursday till 6 o'clock in the evening and every first Thursday of the month we have our "Pizza and Beer" party!!
This is a kit of the following items.
|1x||E3D v6 - Blue Silicone Sock|
|1x||E3D v6 - Blue injection molded fan duct|
|1x||E3D v6 - Heatbreak ( 3 mm )|
|1x||E3D v6 - Heater block including spare fixings (cartridge version)|
|1x||E3D v6 - Heatsink for direct drive ( 3 mm )|
|1x||v6 - Brass Nozzle - 0.40 mm / 3.00 mm|
|1x||Axial Fan 30x30x10mm ( 24 V )|
|1x||Ceramic Heater Cartridge 24 V/40 W ( 150 cm )|
|1x||PTFE tubing, 3.18inner/6outer diameter (80cm)|
|1x||Thermistor cartridge + cable (1m)|
|1 - 9:||excl $ 71.50|
|10 - 29:||excl $ 67.75|
|30 - :||excl $ 64.50|
|Need a larger quantity? Contact our Sales department.|